TECPEL CO., LTD. Tel: 886 2 2218 3111 Fax: 886 2 2218 3222
Bench top LCR Meter
LCR-2200 20~ 200KHz 15025點, 0.1% Basic Accuracy
LCR-2100 50Hz-100kHz, 34 points 0.1% Basic Accuracy
Introductions:
LCR-2000 series is a high precision LCR meter with the latest technology and high density
Circuit design LCR tester, LCR-2000 series is the new generation LCR.
The performance of the instrument can replace the traditional mechanical power switch, using software
Control the power switch. Basic accuracy of 0.05%
Test stability can be more accurate than those of the United States.
LCR-2000 series LCR meter with 4.3-inch TFT LCD display and new interface system
It has an elegant appearance and is easy to operate. Some models integrate transformer testing capabilities,
This improves production and testing efficiency. Moreover, it provides various interfaces and good
Compatible with SCPI commands, the LCR-2000 series of LCR instruments can easily constitute a variety of
Testing system to meet various needs of inspection, production, technology and research and development.
Model |
LCR-2100 |
50Hz-100kHz, 34 points |
|
LCR-2200 |
20Hz-200kHz, 15025 points, |
||
Basic measurement accuracy (See details in technical specification) |
LCRZ |
0.05% |
|
DCR, turn ratio |
0.1% |
||
Calibration condition |
Warm up time:≥ 30 s Environment temperature:23±5ºC Signal voltage:0.3Vrms – 1Vrms Zero clearing:after OPEN, SHORT Testing cable length:0 m |
||
Test signal frequency |
LCR-2100 |
50Hz-100kHz , 34points |
|
LCR-2200 |
20Hz-200kHz, 15025 points |
||
Signal source output impedance |
Selectable 30Ω, 100Ω, ±1% @1kHz |
||
AC test signal level |
Normal |
10mV—2Vrms (LCR-2100: 50mV—1Vrms) |
Minimum resolution:10mV, Accuracy:10% x setting voltage+2mV |
100μA—20mArms (TH2830: 500μA—10mA rms) |
Minimum resolution:0.1mA |
||
Constant level |
20mV—1Vrms (LCR-2100 100mV—500mVrms) |
Minimum resolution:10mV Accuracy:10% x setting voltage +2mV |
|
200μA—10mArms (LCR-2100 1mA—5mA rms) |
Minimum resolution:0.1mA |
||
DC bias voltage source (LCR-2100 with no bias voltage source) |
0V— ± 5V |
Minimum resolution:0.5mV, Accuracy:1% x setting voltage +5mV |
|
0mA—± 50mA |
Minimum resolution:0.5μA |
||
Transformer test parameters |
Turn Ratio, Turns, Phase, L, C, Lk, Q, ACR, DCR, Balance, Pin Short |
||
LCR test parameters |
|Z|, |Y|, C, L, X, B, R, G, D, Q, θ, DCR |
||
DCR display range |
0.00001 Ω-999.999 MΩ |
||
DCR polarity configuration |
FIX, ALT |
||
Turn ratio display range |
1:0.001-1000:1 |
||
LCR parameters display range |
|Z|, R, X 0.00001Ω — 99.9999MΩ |Y|, G, B 0.00001μs — 99.9999s C 0.00001pF — 9.99999F L 0.00001μH — 99.9999kH D 0.00001 — 9.99999 Q 0.00001 — 99999.9 θ(DEG) -179.999º — 179.999º θ(RAD) -3.14159 — 3.14159 Δ% -999.999% — 999.999% |
||
Measurement time (≥10 kHz) |
Fast: 75 meas/sec(13ms), Medium:11 meas/sec(90 ms) Slow:2.7meas/sec(370 ms) |
||
Equivalent circuit |
Serial, Parallel |
||
Range mode |
Auto, Hold |
||
Trigger mode |
Internal, Manual, External, Bus |
||
Average time |
1-255 |
||
Zero clearing |
Open, Short, Load |
||
Arithmetical operation |
Direct reading, ΔABS, Δ% |
||
Delay time setting |
0 -- 60.000s, 1ms steps |
||
Comparator function |
10 bins, BIN1~BIN9, NG, AUX |
||
Bin count function |
|||
PASS, FAIL front panel or scan fixture LED display |
|||
Memory |
100 groups of LCRZ instrument setting files 201 test result |
||
Interface |
Control interface |
HANDLER or SCANNER |
|
Communication interface |
USB HOST, RS232C, RS485(option), GPIB(option) |
||
Storage interface |
USB DEVICE (U-disk storage or barcode scan) |
||
Order information:
LCR-2100 100KHz LCR meter
LCR-2200 200KHZ LCR Meter
Comparison chart:
| Model | LCR-2100 | LCR-2200 |
| Basic accuracy | 0.05% | 0.05% |
| Test speed | 13 Time/Second | 13 Time/Second |
| Display screen | 4.3 Inch TFT LCD Display | 4.3 Inch TFT LCD Display |
| Test Voltage | 50mV- 2V | 50mV- 2V |
| Test Frequency | 50Hz - 100KHz | 20KHz -200KHz |
| Signal impedance | 30/100 Ohm | 30/100 Ohm |
